|
|
resin?
Nov 11, 2011 10:38:08 GMT -5
Post by modelhead on Nov 11, 2011 10:38:08 GMT -5
WHATS THE BEST WAY TO CLEAN RESIN BODYS AND PARTS ?
|
|
|
|
resin?
Nov 11, 2011 16:29:16 GMT -5
Post by rustyrat1960 on Nov 11, 2011 16:29:16 GMT -5
 I used what the company(place from which I bought from) said. Whiteout tire bleach, soaked it over night and washed it with soap and water later. Hope this helps? ;D Later Russ 
|
|
|
|
resin?
Nov 11, 2011 21:56:56 GMT -5
Post by Gothic Kustomz on Nov 11, 2011 21:56:56 GMT -5
Westleys bleache white, can get it at the parts store, wal-mart, or the dollar generial, I use the spray bottle, and a tooth brush, scrub it real good, then wash with dawn soap, and I'm good...
|
|
|
|
resin?
Nov 13, 2011 14:57:06 GMT -5
Post by rustyrat1960 on Nov 13, 2011 14:57:06 GMT -5
;D That is the stuff!! I didn't remember it correctly.HA! Old age creeping up on me!!  HA. . . . . hmmmm, that ain't so funny.  What Mike said, for sure!! I used on a '57 Pontiac, (still waiting to be finished too!)! Give it a try! Later Russ |
|
bcfan
New Member
Posts: 18
|
resin?
May 1, 2015 16:48:14 GMT -5
Post by bcfan on May 1, 2015 16:48:14 GMT -5
I make resin castings all the time. All you really need is some mild dish soap and luke warm water. One or two drops of soap in a plastic bowl, (Never clean parts in an open sink!) and swirl them about a bit. Then rinse the parts and air dry. No matter what you do, don't forget the primer.
|
|
|
|
resin?
Sept 29, 2015 11:50:53 GMT -5
Post by modelhead on Sept 29, 2015 11:50:53 GMT -5
thanks
|
|
|
|
resin?
Sept 29, 2015 23:45:40 GMT -5
Post by Gothicz House Of Kustomz on Sept 29, 2015 23:45:40 GMT -5
I make resin castings all the time. All you really need is some mild dish soap and luke warm water. One or two drops of soap in a plastic bowl, (Never clean parts in an open sink!) and swirl them about a bit. Then rinse the parts and air dry. No matter what you do, don't forget the primer. Ya make resin allot huh? what do ya use as a mold release, , just looking for a easier trick, I have used everything from vasline, to pam, course I use the same mold about 100 times, so like I said, what do ya use |
|
bcfan
New Member
Posts: 18
|
resin?
Oct 1, 2015 20:14:09 GMT -5
Post by bcfan on Oct 1, 2015 20:14:09 GMT -5
Believe it or not, the only mold release I use is rubber to rubber, when making a two part mold. Vaseline is a terrible mold release because it's way too thick. Pam can be used but very sparingly and will leave a residue. WD-40 can be used, but should only be used with platinum cure silicone. It has long term adverse effects on tin cure silicone.
If you need a mold release to pull parts you should switch to Smooth on silicone, or the company that supplies them. The silicone is self degassing and needs no release agent.
rawmaterialsuppliers.com/ |
|
